MTL Attachments (404) 433-5364 - MTL XCT (Xtreme Cutter w/ Teeth)

   The MTL attachments XCT -Xtreme Rotary Brush Cutter uses our tried and proven XC7 deck systems with the upgraded 3-Blade Double Flywheel with Replaceable CARBIDE TEETH used for MULCHING the cut debri and an impressive 7" Diameter cutting capability for your Skid Steer it has a DIRECT DRIVE-POWER HYDRAULIC DRIVE MOTOR – meaning these have no weakpoint gearboxes. Our direct drive units offer a massive 3+” diameter output shaft and are fully serviceable, Most companies will use a pressed bearing housing making them non-serviceable and basically a throw away $500-$700 part if a bearing needs replaced – OURS DO NOT – ours can be serviced with new bearing available for $35 after the 1 year warranty should expire. This is a critical buying point for all customers looking to run a brush cutter, very few cutters are on the market for less than $9,000 that will offer this type of option for you.

THIS UNIT DOES NOT REQUIRE A CASE DRAIN LINE TO OPERATE - you only need the 2 standard lines to operate the new 2020 XCT’s

If your looking for a cutter that is as wide as your tracks are , please make sure you check our measurements   Cutting width and over all width vary on units                                                                                 

Please do not be fooled by many of our competitors copying our design and trying to pass it off as an MTL cutter - 
TRUE  MTL cutter will ALWAYS HAVE the mesh style front grill, and our signature double flywheel design, Along with the Registered Trademark "MTL" logo cut into the motor hood - while some may look the same- they will in no way shape or form - perform like a true MTL, most Copies only have 3/16 decks-1/2 hoses and


ALL MTL Attachments are MADE IN THE USA using USA Steel                                                                                    

The MTL Attachments XCT Xtreme Cutter is an unbelievable land clearing machine. Now with up to 18 Carbide Tipped Teeth.
Use the MTL Attachments Xtreme Cutter to clear property line, gas lines, and building lots. 
The MTL-X is capable of cutting up to 7" diameter trees. 
The MTL-X Cutter features a TRUE DIRECT DRIVE motor system, which means there are no belts, chains with gears to break. 
Solid steel deck plate with Custom extra heavy duty push bar and open face front.
Plus angled steel inside runner on each side.
Complete with hoses & Couplers
NEW FOR 2020 - 3/4" HYADRAULIC HOSES w/ 1/2" standard ISO Flat face couplers ( high Flow Models will come with choice of 3/4 , 5/8 or 1/2 High Flow FFC couplers included in the pricing)
Comes with FORGED External pressure relief valve (PRV)
Integrated Barb wire / wire wrap prevention ring on Spindle assyl
Extra Blade & Bolt kits easily available (From $240 for a set of all 3 blades, Bolts, Nuts)
NEW FOR 2020 Doubled (upper & Lower ) AR steel Plates with Hardened blade sandwiched between the solid steel Flywheel design with integrated balancing 
NEW FOR 2020 AR400 solid Steel  Blades 6" wide double edged blades / Extreme duty AXE style cutting blades – Replacement Blades will be our new “STINGRAY’ Forged and heat treated 5160 steel blades – an Industry First on Cutters under $9,000.
NEW FOR 2020 - New Style-  Extra Hi-Torque drive motor
NEW FOR 2020 - New Style-  Front protective guard (slotted for perfect view)
NEW FOR 2020 - 1/4” Solid Steel Deck  
NEW FOR 2020 - Capped and welded end Caps
NEW FOR 2020 - NEW Greasable bearing housing - make for nearly maint free operation - no more oil bath housing that could fail and go unnoticed
Custom welded FLANGE w/ 6 bolt doubled carrier drive unit withstands almost any conditions
Bi-Directional operation - the MTL XC7 and XCT Extreme cuts in both forward and backward (reversible) - (2020 All units are shipped with the the new Forged Pressure Valve Block , with integrated braking and capable of reversing from inside the cab if needed)

available is the 20- 37 GPM - High Flow Option 1
available is the 30- 45 GPM - High Flow Option 2

NEW FOR 2020 - Now offered in HIGH FLOW UPGRADED – Extreme version Forged Pressure Block for units providing up to 4000 psi and extreme conditions using the High Flow motors.

These units may be purchased as standard flow initially and then upgraded at any point in time to high flow - an industry first and only available at MTL
38,000 lb impact rated bearing carrier - supports the most severe conditions imaginable 

Universal quick connect system - fitting 99% of all skid steers produced.
Compare to the Bradco Ground Shark  @ $9,000 - Blue Diamond @ over $7500

We have available Brand NEW 60" & 72" and now our 78" model MTL Direct Drive units in both Triple Gloss Black & Kubota / Bobcat Orange - 
( please make sure to let us know in the check out section if you would like Orange, default is Black on the cutters)
100% Powder coated assembly - no painted junk
please call 404-433-5364 for additional details or custom ordering options.

Proudly made in the USA
1 year limited warranty on drive system & any manufacturer Defects 

Units are Normally in stock and ready to ship (we sell on avg 150 cutters per month so there is a constant supply of stock) Time to ship out will vary - click on our shipping tab for current info.
**************** Shipping Cost is FREE to the lower 48 States to a Commercial Address or YRC terminal******************SHIPPING:* To ship at the stated price we will need a commercial building with forklift or loading bay (not a home based business address)
* $FREE also includes to your Local YRC freight terminal - you can check your closest terminal at YRC.com* Must be a direct service with YRC freight (CA, WA, OR, MT, WY, UT, ID may be subject to additional charges)
* Please make sure to provide your business name, address, and phone number. These are shipped via commercial freight carrier YRC Freight, XPO or other.
* Residential Delivery is available with an additional charge only $40 here on our site
* Will ship from Our warehouse in Waco, GA 30182 


RETURNS
**Return's Must be as New with All Freight Cost the responsibility of the Buyer

Please call or message me if you have any questions or would like to come inspect one of the units

***Common Questions***
What is the advantage / disadvantage to 3 or 4 blades ?
The most common misconception in the industry is the more blades, the better- Not always correct. The single largest problem with any hydraulic cutter is being able to maintain cutting speed / RPM. If you take For Example 3- blades spinning at 750 rpm this is approx 2250 impacts per minute on the blades, this is also 2250 times per minute that there is an attempt to slow the rpm's (revolution per minute) of the cutter - a 4 blade would be 3000 impacts per minute, and 3000 times per minute at an attempt to slow the rpm's.  We have found that the 3 blade is the best of both worlds, it offers a very good cut on pasture land grass while maintaining the performance in the larger diameter trees and brush. If your machine is toward the upper limit of the Flow chart, then the 4 blade may be a very good option for you.

Does the unit come with the couplers needed to plug into my machine ? -
Yes the unit is ready to go when it arrives - you will need nothing to start operating the unit.

Does the unit really take down 7" diameter trees? -
Yes, infact our customers once they have got familiar with the cutters & cutting larger diameter trees- they have taken down 10" Pine trees and a few 12" Sweet Gum trees, of course the Oaks and hardwoods are still around 6"-7' max.

What is the advantage of the doubled flywheel carrier ? 
If you look on the market you will find there are some similar models offered, and most all of them are single plate carriers, during our testing and development we found the single carriers while cutting overgrowth, and grass work great, but on larger diameter material, they have a greater chance of bending, the double stack flywheel - increases the strength of the design by nearly 3X that of the single stack.